The Roll-A-Door® Series 2 Light Industrial rolling door has long been the ideal choice for industrial and commercial applications.

It features a higher standard of durability, performance and operational ease.

Curtain Qualities

Continuous brake pressed steel curtain. Manufactured from 0.5mm gauge, flexible steel curtain, pressed to a horizontal ribbed profile, sliding between vertical guides.

Deep rigid channel grooves. Aluminium bottom rail with weather seal. Sizes up to 5100mm high x 5500mm wide or up to 3300mm high and 5500mm wide for non-windlocked configurations


Prevents penetration of moisture and dust, thereby minimising the chance of corrosion. Strong, while providing an attractive appearance. Added protection against dirt, leaves and weather.

Smooth, Quiet & Easy Operation

Nylofelt® is used to minimise friction at the working surface. Continuous smooth, quiet operation is an ongoing benefit of this product, without so much as a touch of lubricant.

Secure Locking

Waist high slide bolt locking is located internally and supplied on the left hand side as standard. Waist high internal slide bolt located on right hand side or both sides.

No bending required to unlock doors. Ensured security. Optional centre lift lock with external key and internal knob operation, or internal and/or external bottom rail slide bolt locking.

Easy Opening

The gearing assembly is mounted inside the door roll to minimise side clearance requirements and with its no maintenance, low friction characteristics, provides low operating effort to open and close very large doors. Features include:

  • Doors up to 2400mm high can be operated by hand without the need of chain wheel equipment
  • Doors between 2400mm and 3000mm use efficient direct chain drive
  • Doors over 3000mm high use efficient, compact, planetary reduction gearing
  • Quiet and durable nylon gearing
  • Ease of single handed operation
  • Gearing components require no lubrication due to materials used in manufacturing
  • Balanced loading and withstands very high overload forces without ill effects


B&D Series 2 Light Industrial Roll-A-Doors are available in an extensive range of standard Colorbond® colours including special Zincalume® coated finishes. Zincalume® coated finish can be polyurethaned on site for even wider colour selection.


No greasing of the door guides is required, and the axle, hubs and all other working components have either been manufactured with self-lubricating materials or greased at the factory.

To reduce operational and replacement costs, curtains are easily repaired.


B&D provide tapered curtains to suit floors with a slope across the opening. Optional electric and remote operation are available.

Wicket Gates

Wicket gates provide quick and easy access in or out of the premises, without the need to raise the door. Features include:

  • Opening size is 1780mm high x 600mm wide. This gate is specified when inward opening is required
  • Fitted with external key operated night latch lock
  • When the door is in the open position the cranked bottom rail hangs 65mm below the lintel

Ventilated Curtains

Where ventilation is required the doors may be perforated to allow light penetration or up to 10% airflow. This offeres you all the security you may need plus airflow.

Mullions for Multiple Doors

Where a choice of partial or total access to the building is required, a combination of mullions and multiple Roll-A-Door® Series 2 – Light Industrial rolling doors is  recommended, rather than one wide door. Motorisation is not recommended with mullions. Features include:

  • Mullions can be simply disengaged to provide unrestricted full width access
  • Mullions for smaller doors lift out by hand
  • Individual low effort operation
  • Privacy and weather protection of a small opening

High Wind Rated Roller Door

The B&D Roll-A-Door® S2 roller door been independently certified for use in all cyclone-affected regions throughout Australia.

Our wind-locking technology incorporates a unique clip design  fitted to the edge of every flat on our high wind rolling doors. When exposed to high wind situations, this clip design ensures the door is held captive in the door track, it reduces the risk of both blow-in and blow-out wind forces, and provides added protection against forced entry.

In any area that could be affected by high wind or extreme weather conditions, B&D recommend the fitting of Windlock Guide Systems

Complies with the high wind requirements stated in the National Construction Code*.

*The B&D Roll-A-Door® S2 roller door has have been tested in accordance to the wind requirements of AS/NZS 4505:2012 (Garage Doors & Other large Acess Doors) which complies to AS/NZS 1170.2:2011 (Wind actions) and AS 4055:2012 (Wind loads for housing)

The NT Deemed to Comply Manual (DTCM) is referenced in the Building Code of Australia, Volume 2, Part 3.10.1 as an acceptable construction manual for high wind areas.

The Manual contains products or systems which have been assessed for structural adequacy for cyclonic wind loads and approved by the NT Building Advisory Committee (BAC). These drawings can be accepted by architects, builders, building certifiers, designers, engineers etc as complying with the structural requirements of the NT Building Act.

B&D’s DTCM drawings can be downloaded via the DTCM website or by clicking here.